ASME Y14.5-2009 Dimensioning and Tolerancing
|
ID： |
A96576774E594BB7AC3BE13DED9F9DCF |
|
文件大小(MB)： |
16.11 |
|
页数： |
227 |
|
文件格式： |
|
|
日期： |
2024-6-22 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
A N I N T E R N A T I O N A L S T A N D A R D,ASME Y14.5-2009,[Revision of ASME Y14.5M-1994 (R2004)],Dimensioning,and Tolerancing,Engineering Drawing and Related,Documentation Practices,Copyright ASME International,Provided by IHS under license with ASME Licensee=FMC Technologies /5914950002,No reproduction or networking permitted without license from IHS Not for Resale, 05/07/2009 00:24:44 MDT,--`,,`,,,``,`,``,,``,`,`,,,`,`,`-`-`,,`,,`,`,,`---,-标准下载,http://,ASME Y14.5,ADOPTION NOTICE,ASME Y14.5, Dimensioning and Tolerancing, was adopted on 9 February 2009 for use by the Department of,Defense (DoD). Proposed changes by DoD activities must be submitted to the DoD Adopting Activity: Commander,U.S. Army Research, Development and Engineering Center (ARDEC), ATTN: AMSRD-AAR-QES-E, Picatinny,Arsenal, NJ 07806-5000. Copies of this document may be purchased from The American Society of Mechanical,Engineers (ASME), 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900, http://www.asme.org.,Custodians: Adopting Activity:,Army — AR Army — AR,Navy — SA (Project DRPR-2009-003),Air Force — 16,Review Activities:,Army — CR, IE, MI, PT, TM2,Navy — AS, CG, CH, EC, MC, NP, TD,Air Force — 13, 99,DLA — DH,OSD — SE,NSA — NS,Other — CM, MP, DC2,NOTE: The activities listed above were interested in this document as of the date,of this document. Since organizations and responsibilities can change, you should,verify the currency of the information above using the ASSIST Online database,at http://assist.daps.dla.mil.,AMSC N/A AREA DRPR,DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.,Copyright ASME International,Provided by IHS under license with ASME Licensee=FMC Technologies /5914950002,No reproduction or networking permitted without license from IHS Not for Resale, 05/07/2009 00:24:44 MDT,--`,,`,,,``,`,``,,``,`,`,,,`,`,`-`-`,,`,,`,`,,`---,ASME Y14.5-2009,Dimensioning and,Tolerancing,Engineering Drawing and Related,Documentation Practices,A N I N T E R N A T I O N A L S T A N D A R D,[Revision of ASME Y14.5M-1994 (R2004)],Copyright ASME International,Provided by IHS under license with ASME Licensee=FMC Technologies /5914950002,No reproduction or networking permitted without license from IHS Not for Resale, 05/07/2009 00:24:44 MDT,--`,,`,,,``,`,``,,``,`,`,,,`,`,`-`-`,,`,,`,`,,`---,Date of Issuance: March 27, 2009,This Standard will be revised when the Society approves the issuance of a new edition. There will be no addenda or,written interpretations of the requirements of this Standard issued to this edition.,Periodically certain actions of the ASME Y14 Committee may be published as Cases. Cases are published on the,ASME Web site under the Committee Pages at http://cstools.asme.org as they are issued.,ASME is the registered trademark of The American Society of Mechanical Engineers.,This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The,Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests,have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides,an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large.,ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.,ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this,document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent,nor assumes any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights, is entirely their own responsibility.,Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry,endorsement of this code or standard.,ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures,and policies, which precludes the issuance of interpretations by individuals.,No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.,The American Society of Mechanical Engineers,Three Park Avenue, New York, NY 10016-5990,Copyright . 2009 by,THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,All rights……
……